Posts tagged ‘clothing’

Made my first outfit!

Granted, it is for a doll. But it’s a start.


Whew. This took me a LOT longer than I thought it would. I began with the Wee Wonderfuls jumper pattern, but I cut the skirt piece too short, so I had to improvise the pink ruffle on the bottom. The dark pink fabric is corduroy, which I’ve never used before. Once my sewing machine had its first taste of corduroy, it kept trying to eat it. The needle kept getting stuck and sewing lots of stitches in one spot. Whenever I tried to sew anywhere near the edge of the fabric, it frayed and then the seam opened. Ugh. This was also my first try at sewing darts and straps, or any type of clothing for that matter, so I guess I shouldn’t be surprised that it was such slow going.

I’m very happy with how it turned out, thank goodness. Tomorrow, I’ll give this doll and her new jumper to my niece for her birthday. Hopefully my rookie sewing can hold up to the abuse (err, I mean love) of a four-year-old!


December 1, 2007 at 4:22 pm 5 comments

I used to be a sweater…

…and now I’m a cozy pillow.


I just love this pillow! Recently, one of my lambswool sweaters escaped my notice and ended up in the dryer. When I pulled it out, to my great disappointment, it was really fuzzy and too small for me to wear. I didn’t want to part with it, so I made this pillow.

It was a very simple project. I used my sewing machine for most of the sewing, so it took me less than an hour to complete. I cut out two pieces of the same size and shape from my sweater, put the right sides together, pinned, and sewed all sides together (leaving about four inches open for turning and stuffing.) Then I turned it right-side out, used a pencil to pop to corners out, and stuffed it with polyfill. Then I used a whipstitch to close the opening. Knit fabrics like this are very forgiving– there’s no need to stitch perfectly, because once you pull the stitches tight you can’t even see them.

I love settling in with a book and this pillow in the evening. It’s so soft and it’s just the right size (unlike the shrunken sweater!) As the holiday season approaches, which too often becomes a time of excess, I love knowing that I made something that otherwise would have been discarded into something that will have a place in my home for a long time to come.

November 19, 2007 at 8:42 pm 3 comments

Fun With Freezer Paper


I know I am a little behind the times. I am just now discovering so many great ideas that have been floating around the blogosphere (oh, I can’t say that without laughing…) for a long time now. One such idea is the freezer paper stencil. I was so excited when I discovered Angry Chicken’s tutorial on these. Using freezer paper to make stenciled shirts is ideal for me because (1) I am picky and I want T-shirts that look exactly the way I like them, (2) I am cheap and don’t want to pay more than a few bucks for anything, and (3) I have a short attention span for this sort of thing, and this project only takes a few minutes to complete. You do need to wait a while for the paint to dry– so all you instant gratification seekers out there, don’t try using a hair dryer, waiting thirty seconds and then frantically peeling of the stencil. That won’t work. Trust me. You’ll ruin the shirt and then be mad you wasted $2.99 (see #2).

Freezer paper works great for this project because it is shiny on one side only, so you can easily iron it only fabric and then peel it off when you’re done stenciling. Here’s what I did: I drew a simple sketch. Since I’m new at this, I didn’t want to try anything fancy. I like simple designs anyway. When you’re drawing, you have to think about what part will be painted on the shirt and what will be negative space (the color of your shirt.) If you’re brave you could try using more than one color by stenciling in layers. This would take a longer so I didn’t try it (see #3.)

When I was happy with my sketch, I cut it out using an X-Acto knife. You want to cut your design with the shiny side of the freezer paper down. For this design, the stencils I needed were a piece of freezer paper with a pear shaped hole cut out of it, and two tiny freezer-paper eyes and a mouth. What you’ll need will vary, just figure out what area of your design will need to be painted and what will be negative space– the freezer paper needs to cover all of the negative space in your design.

Next, I ironed a piece of freezer paper inside the shirt behind where my design was going to be. (Put the iron against the papery side, not the shiny side, obviously.) This kept the stencil from slipping while I was painting it, and it also kept the paint from bleeding through the fabric. Then I ironed my stencil into place: first I placed the paper with the pear-shaped hole in it exactly where I wanted it, shiny side down, and iron it to the shirt. Then I placed my pear eyes and mouth when I wanted them, shiny side down, and ironed them into place. In stencil-parlance (ahem), the eyes and mouth are called islands because they’re not attached to the main stencil. The smaller your islands are, the harder it’s going to be to peel them off the shirt once they’re covered with paint, so I wouldn’t advise making them any smaller than I did!

Once my stencil was secured, I painted using a foam brush and fabric paint. I used Tulip Matte Soft Fabric paint from JoAnn’s. It worked well, and it looks pretty good except that I wish it looked a little bit smoother. You might find a paint that you like better (and if so, I’d like to hear what it is!) I covered the area evenly without letting it get too gloppy. Once it dried, I put on another coat because I could still see some of the black shirt coming through. Once I was satisfied with the coverage, and having learned a valuable lesson the first time I tried to peel the stencil off too soon, I let it dry completely by leaving it overnight. The next morning, I carefully peeled off the stencils. When peeling those tiny islands off, I used the X-Acto knife a little bit to guide the paper as it peeled off the shirt, being very careful not to cut the shirt in the process.

Now I have a lovely smiley pear T-shirt! Next, I want to make an angry ice-cream cone T-shirt for my husband. I will try to resist the urge to make the cone say “Eat Me!” so that the shirt can be worn in mixed company.

For more information and inspiration, here are links to the sites I consulted before beginning (I basically followed Angry Chicken’s post step-by-step):

Angry Chicken’s Elf Tee

Crafster’s Tutorial

Flickr page with TONS of inspiration

November 14, 2007 at 8:01 pm 3 comments

Contact Me

Top Posts

January 2020
« Sep